8 Best Low Profile Floor Jacks (November 2026)

The best low profile floor jacks include the AV Steel 2.5 Ton Low Profile Floor Jack for routine sedan maintenance, the AV Steel 3 Ton Low Profile Floor Jack for frequent garage work, and the BIG RED 2.5 Ton Low Profile Trolley Jack for occasional car maintenance.

On this page (9 sections)

1. How we chose the best low profile floor jacks
2. The best low profile floor jacks for different vehicles
3. What should you measure before buying a low profile floor jack?
4. Which pump, saddle and frame features matter?
5. Can a low profile floor jack lift an SUV?
6. How do you set up and use a low profile floor jack safely?
7. How should you care for a low profile floor jack?
8. What mistakes should you avoid with a low profile jack?
9. Which best low profile floor jack fits your work?

The best low profile floor jack for compatible passenger cars is the AV Steel 2.5 Ton Low Profile Floor Jack, as long as its lift range covers your work. LARBANKE is the stronger fit when you need a lower starting point and more height.

Choose around your vehicle's lifting points and planned jobs. A jack that clears the bumper can still fall short on reach, capacity or the height needed to place stands.

Start with our guide to what a low-profile floor jack is if the terms are new. Our floor jack size guide helps connect those measurements to your vehicle.

Our picks at a glance

1. 1
   Best for routine sedan maintenance

   AV Steel 2.5 Ton Low Profile Floor Jack

   8.6/10 our score

   See it on Amazon
2. 2
   Best for frequent garage work

   AV Steel 3 Ton Low Profile Floor Jack

   8.3/10 our score

   See it on Amazon
3. 3
   Best for occasional car maintenance

   BIG RED 2.5 Ton Low Profile Trolley Jack

   7.9/10 our score

   See it on Amazon

4. 4

   SATA 3 Ton Ultra Low Profile Steel Floor Jack

   Best for careful lowering control
   Check it
5. 5

   LARBANKE 3 Ton Dual Piston Floor Jack

   Best for lowered car garages
   Check it
6. 6

   Yellow Jacket 2.5 Ton Aluminum and Steel Floor Jack

   Best for cars with clearance
   Check it
7. 7

   LiftMaster 2.5 Ton Low Profile Floor Jack

   Best for low sedans
   Check it
8. 8

   Bonnlo 3 Ton Low Profile Floor Jack

   Best for higher lifting needs
   Check it

How we chose the best low profile floor jacks

We compared entry height, maximum lift, capacity and handling features, with passenger-car fit as the main priority. A smaller jack earns its place when it covers the job without adding unnecessary carrying weight.

Pump design matters for repeated lifting, while saddle design and casters affect positioning. Neither can make up for a jack that can't reach an approved lifting point.

Conflicting measurements also affect the choices here. AV Steel's 3 ton model and SATA need entry-height confirmation, while Yellow Jacket calls for a more cautious clearance allowance.

The order reflects the scores, but your measurements should decide the purchase. A lower-ranked model can be the right choice when its range solves a need the top pick cannot.

The best low profile floor jacks for different vehicles

Choose the smaller passenger-car models for modest lifting needs, and compare the taller models when your work requires more height. The notes below explain where each pick fits and when to pass.

AV Steel 2.5 Ton: best low profile floor jack for routine car work

1

AV Steel 2.5 Ton Low Profile Floor Jack: Best for routine sedan maintenance

8.6/10Our score

• 3.4 in minimum height
• 14.6 in maximum lift
• 2.5 ton capacity
• Single-piston pump

A focused choice for passenger cars that don't need a tall lift. Its smaller steel frame makes more sense than a larger garage jack when the range fits your work.

See it on Amazon

Pros

• 30 lb weight
• Rotating saddle
• Overload protection

Cons

• Not recommended for trucks or SUVs
• Limited maximum lift

Choose this AV Steel for a passenger car with modest lift-height needs. Its 3.4 to 14.6 in range covers a narrower set of jobs than the larger models, so check stand placement before buying.

The single-piston pump suits buyers who don't need to prioritize rapid lifting. A rotating saddle helps with alignment, but the contact surface must still match the vehicle's approved lifting point.

At 30 lb, the steel jack is a more manageable carrying option than the heavier garage picks. Its rear rotating wheels help you steer it into place on a suitable floor.

Skip it for trucks, SUVs and lifted vehicles, which AV Steel does not recommend for this model. Also pass if your car needs more height to unload the suspension or accept the required stands.

Its appeal is straightforward: buy the smaller tool when it fully covers the work. Don't choose it merely because its capacity sounds large enough.

AV Steel 3 Ton Low Profile Floor Jack

2

AV Steel 3 Ton Low Profile Floor Jack: Best for frequent garage work

8.3/10Our score

• 3 ton capacity
• Dual-piston pump
• 360-degree rotating saddle
• Steel construction

A dual-piston pump and taller lift suit regular garage jobs. Resolve the conflicting minimum-height figures before choosing it for a car with tight clearance.

See it on Amazon

Pros

• Taller lift than smaller AV Steel model
• Dual-piston pump
• Rotating saddle

Cons

• Minimum-height measurements conflict
• Vehicle fit needs confirmation

Choose the larger AV Steel for regular garage work requiring more lift, once you confirm entry clearance. Its advertised range starts at 3-1/8 in and reaches 19-7/8 in, but another minimum-height figure conflicts.

That conflict matters most for a lowered car where a small difference can prevent access. Ask AV Steel to confirm the collapsed saddle height for model AV-300102F before committing to a tight fit.

The dual-piston pump reduces handle strokes compared with a single-piston design. That is useful when you repeatedly raise vehicles for wheel changes or other planned maintenance.

Its steel construction, rotating saddle and rear swivel wheels suit garage positioning. AV Steel also states that it meets ANSI/ASME PASE safety standards.

Skip this model if you need a confirmed low entry and can't resolve the measurement. For alternatives with similar capacity, compare our best 3 ton floor jacks alongside your vehicle's height requirements.

BIG RED 2.5 Ton Low Profile Trolley Jack

3

BIG RED 2.5 Ton Low Profile Trolley Jack: Best for occasional car maintenance

7.9/10Our score

• About 3.3 in minimum height
• About 15 in maximum lift
• 2.5 ton capacity
• Steel construction

A smaller steel option for car owners whose jobs don't require much lift height. Its 27.7 lb weight is easier to plan around than the heavier garage models here.

See it on Amazon

Pros

• 27.7 lb weight
• Steel and swivel casters
• Overload protection

Cons

• Limited maximum lift
• Single-piston lift pump

Choose BIG RED for occasional car maintenance when a smaller steel jack covers the task. Its roughly 3.3 to 15 in range makes it a closer alternative to the smaller AV Steel than to the taller garage models.

The 27.7 lb weight matters if you need to move the jack between storage and the work area. It's still a lifting tool that needs careful handling, especially around shelving or steps.

Steel casters and swivel casters help with positioning. Keep their path clear so the jack can move as the lifting arm rises.

Its single-piston pump makes more sense for occasional work than for buyers focused on fewer handle strokes. BIG RED includes overload protection, but you must plan the load before lifting.

Skip it if an SUV or other vehicle needs substantial height before a wheel leaves the floor. Broad vehicle compatibility is less useful than knowing the exact lift required for your job.

SATA 3 Ton Ultra Low Profile Steel Floor Jack

4

SATA 3 Ton Ultra Low Profile Steel Floor Jack: Best for careful lowering control

7.5/10Our score

• 3 ton capacity
• Dual-piston pump
• Slow-release system
• Steel construction

SATA's slow-release system makes this worth considering when lowering control is a priority. Its conflicting entry heights need to be resolved before buying for a low car.

See it on Amazon

Pros

• Slow-release system
• Dual-piston pump
• Overload protection

Cons

• Minimum-height measurements conflict
• Weighs 70 lb

Consider SATA when lowering control is a priority, provided its confirmed entry height clears your vehicle. SATA describes a slow-release system alongside its dual-piston pump and overload protection.

The minimum-height figures conflict at 2.13, 2-11/16 and 3-3/4 in. Don't choose between those numbers by assuming the smallest one applies to your jack.

Its stated maximum lift is 19-1/8 in, making it an option for jobs beyond the smaller passenger-car models' range. The 70 lb steel construction favors storage near the work area.

A slow-release feature doesn't remove the need to learn the valve's response. Follow SATA's instructions and use small, controlled movements when lowering.

Skip this pick if you frequently carry a jack or cannot confirm clearance for a low car. It makes more sense for a fixed garage space where its lowering system is useful and its dimensions have been settled.

LARBANKE 3 Ton Dual Piston Floor Jack

5

LARBANKE 3 Ton Dual Piston Floor Jack: Best for lowered car garages

7.1/10Our score

• 2.87 in minimum height
• 19.69 in maximum lift
• 3 ton capacity
• Dual-piston pump

A low entry and taller lift suit garages working around low cars. A removable handle and replaceable rotating saddle add practical storage and service features.

See it on Amazon

Pros

• Low entry height
• Removable rotating saddle
• Rubber saddle and foam handle bumper

Cons

• Weighs 70 lb
• Low saddle height doesn't confirm underbody reach

Choose LARBANKE when low entry and taller lift both matter. Its 2.87 to 19.69 in range gives low-car owners more room at both ends than the smaller passenger-car picks.

The rubber saddle rotates and can be removed and replaced. That is useful for service, but any replacement or adapter must be approved for the jack and match the vehicle's lifting point.

A foam handle bumper helps limit contact damage. It doesn't make it safe to let the handle rest against painted bodywork while pumping.

The removable handle helps with storage, while front casters and rear swivel casters support positioning. At 70 lb, this carbon steel model is better suited to rolling around a garage than frequent carrying.

Skip it if a lighter jack already covers your car's needs. For lowered vehicles, also measure the path to the lift point, because a low saddle alone doesn't confirm that the frame will clear.

Yellow Jacket 2.5 Ton Aluminum and Steel Floor Jack

6

Yellow Jacket 2.5 Ton Aluminum and Steel Floor Jack: Best for cars with clearance

7.1/10Our score

• 2.5 ton capacity
• 18-5/16 in maximum lift
• Dual-piston pump
• Aluminum and steel construction

A taller-lifting alternative to the smaller 2.5 ton picks when entry clearance isn't tight. Its mixed-metal build still requires planning for a substantial carrying weight.

See it on Amazon

Pros

• Dual-piston pump
• Side positioning handle
• Rubber saddle and foam handle bumper

Cons

• Conflicting entry-clearance claims
• Weighs 56.9 lb

Choose Yellow Jacket for a car with enough entry clearance but greater lifting needs than the smaller 2.5 ton picks can cover. Its maximum lift reaches 18-5/16 in.

Allow for the stated 3-15/16 in minimum height. A separate 3.5 in clearance claim conflicts, so don't use that smaller figure to plan a close fit.

The aluminum and steel frame weighs 56.9 lb. Mixed-metal construction doesn't make this a light carry, though it weighs less than several steel garage models here.

A side handle helps with positioning, while the dual-piston pump suits repeated lifting. The rubber saddle and foam handle bumper provide contact protection without replacing careful alignment.

Skip it for very low cars unless the clearance has been confirmed. It suits buyers who want more height than a small trolley jack offers and can accept a higher starting point and heavier frame.

LiftMaster 2.5 Ton Low Profile Floor Jack

7

LiftMaster 2.5 Ton Low Profile Floor Jack: Best for low sedans

7.0/10Our score

• 3.15 in minimum height
• 14.5 in maximum lift
• 2.5 ton capacity
• Steel construction

A steel option for low sedans with modest lifting needs. Its lower starting point comes with the shortest maximum lift in this group.

See it on Amazon

Pros

• Low entry height
• Over-pumping bypass device
• Overload protection

Cons

• Shortest maximum lift in this group
• Poor match for jobs requiring more height

Choose LiftMaster for a low sedan with limited height requirements. Its 3.15 to 14.5 in range favors entry clearance over a tall lift.

That tradeoff can work for a car whose approved lifting point is accessible and whose planned jobs need little elevation. Check the height needed for stand placement before treating a low starting point as the deciding feature.

The steel construction includes an over-pumping bypass device and an overload safety valve. These protect against specific operating problems, but they don't turn the jack into a vehicle support.

Its maximum lift is the shortest in this group. Skip it when suspension travel, stand height or access under the car calls for a taller model.

This is a narrow-purpose choice rather than a general answer for every vehicle in the driveway. Buy it when the measured range fits, especially if entry clearance rules out a slightly taller starting saddle.

Bonnlo 3 Ton Low Profile Floor Jack

8

Bonnlo 3 Ton Low Profile Floor Jack: Best for higher lifting needs

6.9/10Our score

• 2.95 in minimum height
• 20.1 in maximum lift
• 3 ton capacity
• Dual-piston pump

The tallest maximum lift here makes Bonnlo worth considering when shorter jacks fall short. Check support-point access and storage space before choosing this heavy steel model.

See it on Amazon

Pros

• Tallest maximum lift in this group
• Low starting height
• Dual-piston design

Cons

• Weighs 70.5 lb
• Extra height doesn't confirm vehicle compatibility

Choose Bonnlo when maximum lift is the deciding need. Its 2.95 to 20.1 in range combines a low starting point with the tallest stated lift in this group.

That extra height can matter when a shorter jack cannot place the vehicle securely on the required stands. It doesn't automatically make Bonnlo suitable for a lifted truck or an unusually deep lifting point.

The dual-piston design suits buyers who want fewer pumping strokes. Swivel front casters help with positioning, but the jack still needs a clear rolling path on a suitable floor.

At 70.5 lb, this alloy steel model belongs on your storage plan before it arrives. Think about the route from its parking spot to the vehicle, including thresholds and tight turns.

Skip it if you need to carry the jack often or don't need its extra height. Our best floor jacks for a home garage covers broader choices for different garage needs.

What should you measure before buying a low profile floor jack?

Measure entry clearance, approach space and required lift height before comparing convenience features. Then confirm the jack's capacity using the vehicle and jack instructions.

Measure the whole path to the lifting point

Check clearance at the approved lifting point and along the route the jack must travel. A bumper, side skirt or underbody panel can block the frame before the saddle reaches its target.

Leave room for positioning rather than planning around an exact, zero-clearance fit. If you need a pinch-weld adapter, include its added height and use only a compatible design.

Also allow space for the handle to move. A saddle that reaches the lifting point is little help if the bumper prevents usable pumping strokes.

If flat-tire work is part of the plan, account for the reduced clearance with a deflated tire. A jack that fits during routine maintenance may not fit in that situation.

Match lift height to the job

Maximum lift describes the saddle's highest position, not the clearance you'll have beneath the vehicle. Suspension travel can use part of that movement before a tire clears the floor.

For stand-supported work, the jack must raise the vehicle enough to place compatible stands at approved support points. Plan those support locations before deciding that a jack's range is enough.

Don't chase extra height without a purpose. A lower lift that safely covers wheel removal may be more useful than a heavy, taller model you struggle to store.

Check capacity without guessing the load split

Follow the vehicle's lifting instructions and the jack's rated limit. Don't assume a corner or axle carries a fixed fraction of the vehicle's total weight.

Vehicle types are broad categories, not capacity calculations. Accessories, cargo and the approved lifting method can change the load you need to consider.

Keep each product's stated ton capacity in view rather than assuming every pound equivalent uses the same convention. If capacity is close or unclear, get guidance before choosing.

Which pump, saddle and frame features matter?

Prioritize vehicle fit first, then ease of use. Pump design, contact surfaces and carrying weight help separate jacks that already meet your lifting requirements.

A dual-piston pump generally raises the saddle with fewer strokes than a single-piston design. That's a useful benefit for repeated work, but it doesn't increase capacity or replace controlled operation.

The saddle must suit the approved lifting point. A rubber surface can help protect contact areas, while some vehicles require a specific adapter rather than a flat saddle.

Consider how often you'll carry the jack, not just how easily it rolls. The heavier models here can stay useful in one garage while being a poor choice for lifting onto a shelf.

Storage also needs room for the handle and access for inspection. A removable handle helps fit the tool into a space, but it doesn't reduce the weight of its frame.

Can a low profile floor jack lift an SUV?

Some can, when capacity, reach and lift height match the SUV. AV Steel excludes SUVs from its smaller model's recommended use, while several other picks describe SUV applications.

An SUV can need more saddle travel before a wheel leaves the floor. A modest maximum lift may be the limiting factor even when the jack fits beneath the vehicle easily.

Check access to approved points, including any required adapters. Don't use a convenient suspension part or underbody panel simply because the saddle reaches it.

A low-profile design is useful for a garage with different vehicles, but it doesn't guarantee broad compatibility. Compare every vehicle you plan to lift against the same checks.

How do you set up and use a low profile floor jack safely?

Use the jack on hard, level ground, and plan the support points before raising the vehicle. Never work beneath a vehicle supported only by a floor jack.

Before first use, read the jack's assembly and setup instructions. Check that required handle connections are secure and inspect for leaks, damage or loose parts.

If the manual calls for air purging or another preparation step, follow that exact process. Don't copy a valve procedure from a different model.

1. Prepare the vehicle. Follow its instructions for parking, transmission position, parking brake use and wheel chocks.
2. Clear the work area. Keep people away and remove loose items that could block the jack's wheels.
3. Position the saddle. Center it at the approved lifting point with the correct contact surface or approved adapter.
4. Take up contact slowly. Stop if the saddle shifts, contacts trim or fails to seat correctly.
5. Raise only as needed. Watch alignment from a safe position and keep body parts clear.
6. Place the stands. Use properly rated supports at approved locations and lower the load onto them as directed.

A floor jack needs room to roll slightly as its arm rises. Don't wedge it in place or use it where its wheels sink into the ground.

Plan how the jack and stands will share the available space. Our guide to how many jack stands you need helps with support planning, while our best jack stands for cars covers stand choices.

For lowering, clear tools and people from beneath the vehicle first. Follow the instructions to remove supports and release the jack gradually, avoiding sudden valve movements.

How should you care for a low profile floor jack?

Inspect it before each use and follow its maintenance schedule. Leaks, bent parts, damaged wheels or irregular lifting are reasons to stop and address the problem.

Keep the wheels and surrounding floor free of grit and debris. Poor rolling can interfere with the jack's movement during a lift.

Wipe away dirt and moisture before storage. Store the jack in the position its manual specifies, usually with the lifting arm lowered.

Use only the hydraulic fluid type and fill procedure required by the manufacturer. Our guide to floor jack oil explains why substitutes and overfilling can cause trouble.

Don't adjust an overload valve to make the jack lift more. If performance changes, follow the approved service process rather than increasing the load or repeatedly forcing the handle.

What mistakes should you avoid with a low profile jack?

Avoid choosing by entry height or capacity alone. The right jack must clear the approach path, reach an approved point and provide enough useful lift.

Don't solve a height shortfall with loose blocks on the saddle. Use only approved accessories, accounting for their effect on clearance and capacity.

Don't assume a rotating saddle will correct poor alignment. Position the jack properly before the vehicle's weight comes onto it.

Don't use the jack to drag or reposition a raised vehicle. Its casters allow movement during lifting, not transport with a load.

Finally, don't treat overload protection as a load calculator. Check compatibility before use rather than relying on a safety feature to stop an unsuitable lift.

Which best low profile floor jack fits your work?

Choose the AV Steel 2.5 Ton for compatible passenger cars when a modest lift covers the task. BIG RED is another smaller option for occasional work, while LiftMaster favors a low entry with limited top-end height.

Choose LARBANKE for low cars needing more lift, or Bonnlo when its extra maximum height solves a measured shortfall. Both require a storage plan that accounts for their carrying weight.

The larger AV Steel suits regular garage work after entry-height confirmation. SATA is worth considering for its lowering system once its clearance is settled, while Yellow Jacket fits cars with more room underneath.

Before ordering, write down your approved lifting point, approach clearance, required height and capacity needs. The best low profile floor jack is the one that meets all four and works with your support plan.

Use our guide to low-profile floor jacks if you need help separating entry height from reach before making the final choice.

Our top 3 picks at a glance

1. 1
   Best for routine sedan maintenance

   AV Steel 2.5 Ton Low Profile Floor Jack

   8.6/10 our score

   See it on Amazon
2. 2
   Best for frequent garage work

   AV Steel 3 Ton Low Profile Floor Jack

   8.3/10 our score

   See it on Amazon
3. 3
   Best for occasional car maintenance

   BIG RED 2.5 Ton Low Profile Trolley Jack

   7.9/10 our score

   See it on Amazon

Frequently asked questions

What makes a floor jack low profile?

A low-profile floor jack has a low starting saddle height that helps it fit beneath cars with limited clearance. The whole approach path must also clear the jack's frame, not just its saddle.

Our guide to what a low-profile floor jack is explains how entry height differs from reach.

How low should a low-profile floor jack be?

Choose a minimum height below the clearance at your approved lifting point, leaving room to position the jack without contact. Measure the route beneath the bumper or side skirt as well.

If you'll use it for flat tires, account for the lower clearance caused by a deflated tire.

Is a 2.5 ton floor jack enough for my car?

A 2.5 ton floor jack can suit some cars, but check the vehicle's lifting instructions and the jack's capacity together. Don't assume every lifting point carries an equal share of the weight.

Use our floor jack size guide to plan capacity, entry clearance and required lift height.

Can a floor jack hold a car while I work under it?

No, never work beneath a vehicle supported only by a floor jack. Transfer the load onto properly rated jack stands at approved support points on a hard, level surface.

See how many jack stands you need, and follow the vehicle, jack and stand instructions throughout the job.